mirror of
https://github.com/CopterExpress/clover.git
synced 2026-05-26 21:19:35 +00:00
70 lines
2.9 KiB
Markdown
70 lines
2.9 KiB
Markdown
# Assembling and setting up a mechanical gripper
|
||
|
||
1. Combine the main gripper plates.
|
||
|
||
<img src="../assets/mechanical_grip/mech_grip_1.png" width=300 class="zoom border center">
|
||
|
||
2. Install the servo in the appropriate groove in the center of the plates with the axle gear in the middle.
|
||
|
||
<img src="../assets/mechanical_grip/mech_grip_2.png" width=300 class="zoom border center">
|
||
|
||
3. Hold down the gripper plates with the small spacers.
|
||
|
||
<div class="image-group">
|
||
<img src="../assets/mechanical_grip/mech_grip_3.png" width=300 class="zoom border">
|
||
<img src="../assets/mechanical_grip/mech_grip_4.png" width=300 class="zoom border">
|
||
</div>
|
||
|
||
4. Install the gripper deck so that the mounting holes in the grapple correspond with the self-tapping holes in the plate.
|
||
|
||
<img src="../assets/mechanical_grip/mech_grip_5.png" width=300 class="zoom border center">
|
||
|
||
5. Fix the gripper structure with self-tapping screws.
|
||
|
||
<img src="../assets/mechanical_grip/mech_grip_6.png" width=300 class="zoom border center">
|
||
|
||
6. Turn the servo gear to the end position.
|
||
|
||
<img src="../assets/mechanical_grip/mech_grip_7.png" width=300 class="zoom border center">
|
||
|
||
7. Install the cruciform mount onto the gear and secure it using the screw attached to the servo.
|
||
|
||
<img src="../assets/mechanical_grip/mech_grip_8.png" width=300 class="zoom border center">
|
||
|
||
8. Cut the cruciform mount.
|
||
|
||
<div class="image-group">
|
||
<img src="../assets/mechanical_grip/mech_grip_9.png" width=300 class="zoom border">
|
||
<img src="../assets/mechanical_grip/mech_grip_10.png" width=300 class="zoom border">
|
||
</div>
|
||
|
||
9. Tie the servo thread so that there is a 2 to 3 cm margin.
|
||
|
||
<div class="image-group">
|
||
<img src="../assets/mechanical_grip/mech_grip_11.png" width=300 class="zoom border">
|
||
<img src="../assets/mechanical_grip/mech_grip_12.png" width=300 class="zoom border">
|
||
</div>
|
||
|
||
10. Thread the servo thread into the corresponding tensioning slots.
|
||
|
||
<img src="../assets/mechanical_grip/mech_grip_13.png" width=300 class="zoom border center">
|
||
|
||
11. Fasten the grip claws with small self-tapping screws so that their angle is 25°–40°.
|
||
|
||
<img src="../assets/mechanical_grip/mech_grip_14.png" width=300 class="zoom border center">
|
||
|
||
12. Install the assembled grip onto the aircraft from below.
|
||
|
||
<div class="image-group">
|
||
<img src="../assets/mechanical_grip/mech_grip_16.png" width=300 class="zoom border">
|
||
<img src="../assets/mechanical_grip/mech_grip_17.png" width=300 class="zoom border">
|
||
</div>
|
||
|
||
13. Insert the servo cable into the *AUX* 1-2 output on the flight controller.
|
||
|
||
<img src="../assets/mechanical_grip/mech_grip_18.png" width=300 class="zoom border center">
|
||
|
||
14. Go to the *Radio* tab to control capture with the remote control.
|
||
15. In the *AUX 1/2 Passthrough RC channel* parameter, select the desired channel.
|
||
16. Now, when you switch the toggle switch of the corresponding channel, the capture will be closed or opened.
|